[SHARED] NaNO_3nGiNe 49R ver 3.0

[ritza_ll]

That coz the param table,
I'm edit the param table.
See the value of bass off, common param table set to 248, but mine 234.
234 have bigger vibe, even vibe sync set off.
U can back set the value to 248 or use other param table.
Thanks

[nishanth_r]

Thanks

[mores]

@ritza II
can you give a little detail how to load the fonts from zh@ng to your lanpack?.tnx..

[mores]

one more...
im having a problem withj this mp when installing java.. it shows installation progress and fininshed. but when i retart nothings happened.. how can i solved this?

[ritza_ll]

Sorry can't give detail step.
Open the LP using MLE.
In tab font, find ID where the multifont located.
Save the font file (*.mff)
Then open your LP, load the mff file to your LP.

About install apps
Read the instruction.
Bfore the progress,
you must delete IMEI number folder in your TF first.

[mores]

ok il try that..

but for install app. im installing it in my phone not flash.. and no existing imei in my flash

[ritza_ll]

In phone?
That's weird, do u install using motomidman 0.8.X?
What do you mean nothin happen?
The apps can't detected?
Did u use other CG1 or other CG2?(not from repack version)
Or undo increase list suite patch?

[x3m]

Ok, my phone is broken so I ended up with a moto e398. It's a really nice phone, I must say. So I flashed it already a few times, revived it as well. So to the question - these megapacks - there are two versions - for e398 and for pokr. If I haven't flashed it to pokr will my phone flash it automatically, or I will have to flash it first to pokr and then use the megapack. I'm asking this because the first method doesn't work for me. When I flash from e398, using a megapack(i tried quite a few) everything goes smooth, but when I try to turn my phone on only a deaden crackle appears but the phone doesn't turn on.

Edit: Actually I tried to flash with megapack after flashing with 42R for all, but the phone still can't be switched on. I force boot with holding down * and # and run the backups or flashing again to 42R for all, but I can't go anywhere from this point on. I searched for the problem on the site, but it seems that noone has had this problem but me. So does anyone have a solution for this? I will be very thankful.

p.s: I use this thread because I want this megapack(actually most of them would work for me), hope the thread starter doesn't mind.

[ritza_ll]

E398 version means for E398/ROKR with boot loader 07.D0
ROKR version is for ROKR with boot loader 0A.02

Try restore your full backup first,
After your phone can turn on again, start the flashing again.

I usually upgrade my E398 from R372 to R373
with this step
1.Flash 42R for all cG7 only (don't turn on the phone, keep it in boot loader menu)
2.Flash any MP for E398

If didn't work
1.Flash 42R for all Full Flash
2.Flash any MP for E398
3.Restore your PDS backup

Don't forget to create 32MB full backup, PDS and BootLoader backup.

[x3m]

Ok, first - thank you for the explanation about the bootloaders, I didn't think in that way. It was my bad. Second - I flashed just as you said and everything worked great. Then I backed-up the PDS and when I turned my phone on the logo shows up, then fades out, followed by white flashing screen. I searched in the forum and found two threads about this problem, but couldn't find replies to clear thing out for me.  I'm currently flashing again to 42r and I will then flash with an MP. However, because of the PDS problem I can't exploit my phone fully. Can you give a solution for this problem? Thanks in advise and again sorry for posting offtopics in this thread.

[ritza_ll]

Wait, Try to turn on your phone without Trans Flash.
May be that caused coz elf.
What previous MP that u used?

[x3m]

No, still the same result. And I've used only your MP so far. One more question - my PC detects the phone BT and connects with the phone. It still shows that the address is FFFFFFFF, though. I can upload and download images. Nevertheless, I can't see them in the phone. I mean I can see the file, but can't open it. Is this because of the PDS and is restoring the PDS a must-do? And one more question - when I connect my PC to the phone through BT I see the files and folders on the phone only. How to access the memory card? Thanks again.

[ritza_ll]

Restore your PDS or fix your BT address.
I never connect to PC throught bluetooth, may be that just setting like in p2kTools how the program read the data, from a/, b/ or c/
CMIIW.

Add build 3.9

[lusifer84]

hi bro,is very nice your MP but a have a problen with the skins when i erasy a skin in the fone yet I see the name and in the skinman not, how I can fix this

[ritza_ll]

Thats caused AP skins patch.
To completely delete skin, u need to delete sub folder first,
c/mobile/skins/name skin/player/audio & video
than the player folder
tHe last is delete the skin.
Use motoCmd.elf to delete the skin, it's fast and easy.