|
Title: DualBoot for L7e, K1 and Z3 Post by: Exploited on September 26, 2007, 09:34:20 am 1. Split the SHX using SHX coded and get CG7
2. In CG7 on address C82 write the following: 48016800470011FE0014 3. Compile new SHX with the updated CG7 + the attached CG18. 4. Flash and be happy with dualboot Use *+#+ON to enter or *+ON for blank mode Title: Re: DualBoot for L7e, K1 and Z3 Post by: error398 on September 26, 2007, 09:38:06 am 1. Split the SHX using SHX coded and get CG7 2. In CG7 on address C82 write the following: 48016800470011FE0014 3. Compile new SHX with the updated CG7 + the attached CG18. 4. Flash and be happy with dualboot Use *+#+ON to enter or *+ON for blank mode i see that E398 can too.. but donno which seems Title: Re: DualBoot for L7e, K1 and Z3 Post by: diabolic53 on October 01, 2007, 04:34:43 am it doesn't work on Z3 tested by me 2 times :(
Title: Re: DualBoot for L7e, K1 and Z3 Post by: Exploited on October 08, 2007, 10:22:00 am make sure that you patch the CG7 correctly
Title: Re: DualBoot for L7e, K1 and Z3 Post by: diabolic53 on October 09, 2007, 05:40:04 am i did :( on that adress and id didn't work... on my CG7 the part that i have to change is filled with FF??? maibe the adress isn't correct
Title: Re: DualBoot for L7e, K1 and Z3 Post by: Exploited on November 04, 2007, 02:02:53 am make sure that you do not insert, but replace the strings - if you add just additional characters it will ruin the cg
Title: Re: DualBoot for L7e, K1 and Z3 Post by: xwinx on February 17, 2008, 02:21:23 am I just try to remove RSA on my Z3 with TP.
But this is happen after i try to remove RSA. I think my Z3 doesnt have a bootloader! *+#+ON, result = whitescreen (detected as S Flash Neptune LTE2) *+ON result = normal boot. My f/w is R452B_G_08.02.0DR and Flex MOTOGeneration (original from TP). I want to use other flex so i try to flash cg2, cg7 and 15 and got an error message when sending a loader (after TP). I think that i dont have a bootloader. How to get a bootloader? Do i need to do TP again? -sorry for my bad english- Title: Re: DualBoot for L7e, K1 and Z3 Post by: anhvu2875 on February 17, 2008, 05:54:21 am I just try to remove RSA on my Z3 with TP. doing hard testpoint and reflash !But this is happen after i try to remove RSA. I think my Z3 doesnt have a bootloader! *+#+ON, result = whitescreen (detected as S Flash Neptune LTE2) *+ON result = normal boot. My f/w is R452B_G_08.02.0DR and Flex MOTOGeneration (original from TP). I want to use other flex so i try to flash cg2, cg7 and 15 and got an error message when sending a loader (after TP). I think that i dont have a bootloader. How to get a bootloader? Do i need to do TP again? -sorry for my bad english- Title: Re: DualBoot for L7e, K1 and Z3 Post by: xwinx on February 17, 2008, 09:37:18 am When i press #+*+On my phone can enter Dual Boot
For Motorola Z3 By GandjaFuzz & Vilko .......... Version 3.3 But my phone cant enter normal mode. TP again? I just try n try.. again n again... Same result. Need an advice here Title: Re: DualBoot for L7e, K1 and Z3 Post by: anhvu2875 on February 18, 2008, 09:28:51 am When i press #+*+On my phone can enter Dual Boot i think u can try another removed RSA MP ! which FM did u flash ?For Motorola Z3 By GandjaFuzz & Vilko .......... Version 3.3 But my phone cant enter normal mode. TP again? I just try n try.. again n again... Same result. Need an advice here Title: Re: DualBoot for L7e, K1 and Z3 Post by: xwinx on February 19, 2008, 01:31:55 am I tried to flash it with MOTOGeneration MP, i think its a RSA Removed MP.
Where i can find other RSA Removed MPs? Title: Re: DualBoot for L7e, K1 and Z3 Post by: anhvu2875 on February 19, 2008, 03:37:25 am I just try to remove RSA on my Z3 with TP. well i think ur problem here : u reflashed CG7 ? But this is happen after i try to remove RSA. I think my Z3 doesnt have a bootloader! *+#+ON, result = whitescreen (detected as S Flash Neptune LTE2) *+ON result = normal boot. My f/w is R452B_G_08.02.0DR and Flex MOTOGeneration (original from TP). I want to use other flex so i try to flash cg2, cg7 and 15 and got an error message when sending a loader (after TP). I think that i dont have a bootloader. How to get a bootloader? Do i need to do TP again? -sorry for my bad english- Title: Re: DualBoot for L7e, K1 and Z3 Post by: xwinx on February 20, 2008, 04:10:17 am And now after trying to get the dualboot my z3 is bricked.
I dunno whats the problem. 1st time i cant power up my z3, also *+ON do not work Then i try #+*+ON, i can go to dualboot screen by GandjaFuzz n Vilko. But it says that S/W is not found. My friend said that it is a pds error. It will be hard to repair it. Even GOTMOTO may be could not help. Any suggestions guys? I prepare to buy GOTMOTO account if it can repair my z3 |